How to Clean and Prime Resin Miniature Bits Before Painting

Priming is the part of the hobby nobody puts on the box art. You've got a fresh pile of helmets and shoulder pads, game night is calling, and the urge to go straight from the mailbox to the spray can is strong. Resist it. Ten minutes of prep is the difference between paint that grips and paint that peels off your favorite sergeant at the first friendly game. Think of it as the "wax on, wax off" of miniature building: boring, repetitive, and secretly the whole point.

How you prep depends on how you bought your bits, so this guide splits into Grey Resin parts that arrive ready to go and Digital STL parts you print yourself. If you haven't picked a format yet, start with Grey Resin, STL or SPEEDY Resin.

First, the safety gear

This is the one section you shouldn't skim. Resin is great stuff, but it asks for a little respect.

  • Nitrile gloves whenever you handle uncured or tacky resin, and when you're working with isopropyl alcohol (IPA). Not latex.
  • A respirator rated for fine particulates whenever you sand resin or use a motor tool on it. That goes for fully cured parts too. A motor tool throws fine dust into the air, and that's not something you want in your lungs. If you'll be around resin or IPA vapors, ask for organic vapor cartridges as well.
  • Safety glasses for anything that can splash or fling. A support nub leaving a motor tool at speed has no respect for your eyeballs.
  • Ventilation. Work where the air has somewhere to go. An open window helps, but a window with moving air helps more.
  • Keep IPA away from flames, sparks and heat. It's flammable. Don't run it in an ultrasonic cleaner you walk away from.
  • Nothing with uncured resin goes down the drain. That includes used IPA and rinse water. Check how your local hazardous waste program wants it handled.

When you're done, wipe your bench with a damp paper towel instead of sweeping dust around, and wash up with soap and water.

Grey Resin: the quick prep pass

Grey Resin parts are printed to order, delivered with every part separate and no sprue, and ready to prime. So you don't have a full post-processing job on your hands. It's still worth a quick pass, because shipping dust and handling oils don't do primer any favors.

These steps assume a typical UV-cured grey resin that washes in IPA.

  1. Inspect and test fit. Check each part and dry fit it. Plenty of hobbyists kitbash our parts with kits from all over their bits box. Every kit is different, so test fit before you glue.
  2. Trim the support nubs. Expect a few small ones. Shave them with a sharp hobby knife, cutting away from your fingers, then smooth the spot with a fine sanding stick. Gloves and respirator on if you're sanding.
  3. Give it a short IPA scrub. Use 90% or stronger IPA and a soft toothbrush. A minute or two is plenty, and don't leave parts soaking, because long baths can damage resin.
  4. Let it dry completely. Set parts on a paper towel and give them time. Trapped liquid and primer don't get along.
  5. Do the touch test. With gloves on, feel the part. It should be dry, not sticky. If a spot is tacky, re-clean it, let it dry, and give it a short session under a UV cure light. Curing a wet part can lock in a sticky film, so dry comes first.

Go gently on thin parts. Resin is built for crisp detail, not flex, so blades like the Arthurian Knights Energy Sword and poles like the Cyber Samurai Sashimono Battle Flag deserve a light hand with the toothbrush. Tiny parts need care too. Shoulder symbols like the Order of Zhe-nos Hellions Knight set are separate pieces, so wash them in a fine strainer or the sink trap will collect a tithe.

Digital STL: read the manufacturer's instructions first

With Digital STL files, you're the factory, which means you own the whole cleanup. Here's the big rule: read the cleanup instructions from your resin's manufacturer, and follow those over anything you read on a blog, including this one.

Resins differ. Some wash in IPA, some are water-washable, and some have their own specialty cleaners. Wash times, cure times and safety data all vary by brand and formula. The bottle, the product page and the safety data sheet are your rulebook. Your printer and wash station instructions matter too.

The usual flow looks like this, with the details coming from your manufacturer:

  1. Gloves on before the build plate comes off. A fresh print is uncured resin, so treat it that way.
  2. Wash in the recommended cleaner. Many printers use a dirty bath and then a clean bath for a better result.
  3. Take off the supports. Many hobbyists do this before the final cure, while they're less brittle. Our STLs are supplied unsupported, so you decide how the supports go on.
  4. Dry completely. Check undersides and hollows for pooled liquid.
  5. Cure as directed. Stop at what the manufacturer recommends. More isn't always better.
  6. Clean up the remnants. Trim, sand and do a final wipe, using the safety gear above.

If a part is still tacky after a proper wash, dry and cure, more alcohol probably won't save it. That often points to your exposure settings, so check them against your resin's recommendations. For the wider picture, see Miniature Building 101: 3D Printed.

Cleaning up support remnants

A sharp knife handles most nubs, and for most bits it's all you need. Stubborn remnants on bigger parts are where a motor tool earns its bench space, and that's where this goes from hobby to hazmat if you skip the gear.

  • Put on your gloves, respirator and safety glasses first. All three. Every time.
  • Run the tool on low speed. High speed can heat and gum up the resin and throws more dust.
  • Use light passes and keep moving, so you don't carve a divot into a helmet crest.
  • Hold the part in a pin vise or clamp if your fingers are close to the bit.
  • Wet sanding by hand is a good alternative for flat spots, since the water helps keep dust down.
  • Wash the part again afterward so dust doesn't end up under the primer.

Fixing small bubbles and gaps

Tiny pits and gaps are easy to fix, and now's the time, because primer shows everything. Use two-part epoxy putty for resin parts, smooth it, and let it cure fully. If you're working on a plastic model in the same build, Sprue Goo is a good fit for plastic-to-plastic gaps, but plastic cement won't bond resin. For resin joints, use super glue. There's more on resin assembly in Miniature Building 101: Resin Minis.

Choosing and using primer

Grey resin takes primer like a dream, so you don't need anything exotic. Any good hobby primer works, and grey is a versatile starting color because it shows detail well and doesn't fight your paint. Test a new can on a spare part first.

  • Spray cans: Hold the can about 25–30cm (10–12in) away and use short, steady bursts. Too close and it pools. Too far and it goes grainy.
  • Brush-on primer: Thin it slightly and use thin, even coats. It's a solid choice for small batches or for winter, when spraying outside is off the table.
  • Thin beats thick: Two light coats keep the detail on your heads and helmets. One heavy coat buries it.
  • Warm and dry: Rattle cans dislike cold, damp air. If the weather isn't cooperating, wait it out or switch to a brush.
  • Give it time: Let primer cure at least an hour before painting. Overnight is better.

Small parts are easier to prime before assembly, mounted on a strip of poster tack or double-sided tape. Glued-on symbols can go either way: prime and paint them on the pad, or paint them first and glue them on as a finishing touch.

That's it. Your Grimdark Future army, Firefight team or Warpath and Deadzone squads get paint that stays where you put it, and you get to keep your lungs.

Ready to stock the bench?

  • Grey Resin: Printed to order in about 4–6 weeks, with no sprue.
  • Digital STL: Instant download, supplied unsupported, with a personal-use license.
  • SPEEDY Resin: A $10 deposit finds a print partner near you, and you get a quote before anything prints. Color may vary.

New around here? The Start Here page explains how everything fits together, and the main conversion bits guide shows which ranges suit which armies.

BW Terrain & Forge is an independent studio and is not affiliated with Games Workshop Group PLC or its affiliates. Our products are original designs, not scans, recasts or replicas. They are not designed, manufactured, licensed or approved by Games Workshop, and are not intended to include or infringe any of its intellectual property. One Page Rules, Grimdark Future, Firefight, Mantic, Warpath and Deadzone are the property of their owners and are mentioned to describe the games our parts are designed for. See our Terms of Use for more information.

0 comments

Leave a comment

Please note, comments need to be approved before they are published.